(1) The director and duly appointed city sealers shall enforce the provisions of this chapter. The director shall adopt rules for enforcing and carrying out the purposes of this chapter including but not limited to the following:
(a) Establishing state standards of weight, measure, or count, and reasonable standards of fill for any commodity in package form;
(b) The establishment of technical and reporting procedures to be followed, any necessary report and record forms, and marks of rejection to be used by the director and city sealers in the discharge of their official duties as required by this chapter;
(c) The establishment of technical test procedures, reporting procedures, and any necessary record and reporting forms to be used by service agents when testing and inspecting instruments or devices under RCW 19.94.255(3) or when otherwise installing, repairing, inspecting, or standardizing the graduations of any weighing or measuring instruments or devices;
(d) The establishment of exemptions from the marking or tagging requirements of RCW 19.94.250 with respect to weighing or measuring instruments or devices of such character or size that such marking or tagging would be inappropriate, impracticable, or damaging to the apparatus in question;
(e) The establishment of exemptions from the inspection and testing requirements of RCW 19.94.163 with respect to classes of weighing or measuring instruments or devices found to be of such character that periodic inspection and testing is unnecessary to ensure continued accuracy;
(f) The establishment of inspection and approval techniques, if any, to be used with respect to classes of weighing or measuring instruments or devices that are designed specifically to be used commercially only once and then discarded, or are uniformly mass-produced by means of a mold or die and are not individually adjustable; and
(g) The establishment of inspection and testing procedures to be used for classes of weighing or measuring instruments or devices found to be few in number, highly complex, and of such character that differential or special inspection and testing is necessary, including railroad track scales. The department's procedures shall include requirements for the provision, maintenance, and transport of any weight or measure necessary for the inspection and testing at no expense to the state.
(2) These rules shall also include specifications and tolerances for the acceptable range of accuracy required of weighing or measuring instruments or devices and shall be designed to eliminate from use, without prejudice to weighing or measuring instruments or devices that conform as closely as practicable to official specifications and tolerances, those (a) that are of such construction that they are faulty, that is, that are not reasonably permanent in their adjustment or will not repeat their indications correctly, or (b) that facilitate the perpetration of fraud.
[1995 c 355 § 9; 1992 c 237 § 9; 1991 sp.s. c 23 § 6; 1989 c 354 § 36; 1977 ex.s. c 26 § 5; 1969 c 67 § 19.]
Notes: Application -- Effective dates -- 1995 c 355: See notes following RCW 19.94.015.
Legislative findings -- Intent -- 1991 sp.s. c 23: See notes following RCW 19.94.150.
Severability -- 1989 c 354: See note following RCW 15.36.012.
(1) The director and duly appointed city sealers shall enforce the provisions of this chapter. The director shall adopt rules for enforcing and carrying out the purposes of this chapter including but not limited to the following:
(a) Establishing state standards of weight, measure, or count, and reasonable standards of fill for any commodity in package form;
(b) The establishment of technical and reporting procedures to be followed, any necessary report and record forms, and marks of rejection to be used by the director and city sealers in the discharge of their official duties as required by this chapter;
(c) The establishment of technical test procedures, reporting procedures, and any necessary record and reporting forms to be used by service agents when testing and inspecting instruments or devices under RCW 19.94.255(3) or when otherwise installing, repairing, inspecting, or standardizing the graduations of any weighing or measuring instruments or devices;
(d) The establishment of exemptions from the marking or tagging requirements of RCW 19.94.250 with respect to weighing or measuring instruments or devices of such character or size that such marking or tagging would be inappropriate, impracticable, or damaging to the apparatus in question;
(e) The establishment of exemptions from the inspection and testing requirements of RCW 19.94.163 with respect to classes of weighing or measuring instruments or devices found to be of such character that periodic inspection and testing is unnecessary to ensure continued accuracy;
(f) The establishment of inspection and approval techniques, if any, to be used with respect to classes of weighing or measuring instruments or devices that are designed specifically to be used commercially only once and then discarded, or are uniformly mass-produced by means of a mold or die and are not individually adjustable; and
(g) The establishment of inspection and testing procedures to be used for classes of weighing or measuring instruments or devices found to be few in number, highly complex, and of such character that differential or special inspection and testing is necessary, including railroad track scales. The department's procedures shall include requirements for the provision, maintenance, and transport of any weight or measure necessary for the inspection and testing at no expense to the state.
(2) These rules shall also include specifications and tolerances for the acceptable range of accuracy required of weighing or measuring instruments or devices and shall be designed to eliminate from use, without prejudice to weighing or measuring instruments or devices that conform as closely as practicable to official specifications and tolerances, those (a) that are of such construction that they are faulty, that is, that are not reasonably permanent in their adjustment or will not repeat their indications correctly, or (b) that facilitate the perpetration of fraud.
[1995 c 355 § 9; 1992 c 237 § 9; 1991 sp.s. c 23 § 6; 1989 c 354 § 36; 1977 ex.s. c 26 § 5; 1969 c 67 § 19.]
Notes: Application -- Effective dates -- 1995 c 355: See notes following RCW 19.94.015.
Legislative findings -- Intent -- 1991 sp.s. c 23: See notes following RCW 19.94.150.
Severability -- 1989 c 354: See note following RCW 15.36.012.
(1) The director and duly appointed city sealers shall enforce the provisions of this chapter. The director shall adopt rules for enforcing and carrying out the purposes of this chapter including but not limited to the following:
(a) Establishing state standards of weight, measure, or count, and reasonable standards of fill for any commodity in package form;
(b) The establishment of technical and reporting procedures to be followed, any necessary report and record forms, and marks of rejection to be used by the director and city sealers in the discharge of their official duties as required by this chapter;
(c) The establishment of technical test procedures, reporting procedures, and any necessary record and reporting forms to be used by service agents when testing and inspecting instruments or devices under RCW 19.94.255(3) or when otherwise installing, repairing, inspecting, or standardizing the graduations of any weighing or measuring instruments or devices;
(d) The establishment of exemptions from the marking or tagging requirements of RCW 19.94.250 with respect to weighing or measuring instruments or devices of such character or size that such marking or tagging would be inappropriate, impracticable, or damaging to the apparatus in question;
(e) The establishment of exemptions from the inspection and testing requirements of RCW 19.94.163 with respect to classes of weighing or measuring instruments or devices found to be of such character that periodic inspection and testing is unnecessary to ensure continued accuracy;
(f) The establishment of inspection and approval techniques, if any, to be used with respect to classes of weighing or measuring instruments or devices that are designed specifically to be used commercially only once and then discarded, or are uniformly mass-produced by means of a mold or die and are not individually adjustable; and
(g) The establishment of inspection and testing procedures to be used for classes of weighing or measuring instruments or devices found to be few in number, highly complex, and of such character that differential or special inspection and testing is necessary, including railroad track scales. The department's procedures shall include requirements for the provision, maintenance, and transport of any weight or measure necessary for the inspection and testing at no expense to the state.
(2) These rules shall also include specifications and tolerances for the acceptable range of accuracy required of weighing or measuring instruments or devices and shall be designed to eliminate from use, without prejudice to weighing or measuring instruments or devices that conform as closely as practicable to official specifications and tolerances, those (a) that are of such construction that they are faulty, that is, that are not reasonably permanent in their adjustment or will not repeat their indications correctly, or (b) that facilitate the perpetration of fraud.
[1995 c 355 § 9; 1992 c 237 § 9; 1991 sp.s. c 23 § 6; 1989 c 354 § 36; 1977 ex.s. c 26 § 5; 1969 c 67 § 19.]
Notes: Application -- Effective dates -- 1995 c 355: See notes following RCW 19.94.015.
Legislative findings -- Intent -- 1991 sp.s. c 23: See notes following RCW 19.94.150.
Severability -- 1989 c 354: See note following RCW 15.36.012.
